男女做受性高爱潮叫床动态图

    <thead id="pbhjt"><menuitem id="pbhjt"></menuitem></thead><video id="pbhjt"><mark id="pbhjt"></mark></video>

    <delect id="pbhjt"></delect>
      <span id="pbhjt"></span>
      <sub id="pbhjt"><th id="pbhjt"></th></sub><del id="pbhjt"></del>
      <span id="pbhjt"></span>

            <track id="pbhjt"></track>

            <track id="pbhjt"></track>

                脫模劑系列

                News information

                推薦產品

                Recommended products

                • GW4000

                  GW4000

                • PM-1625W

                  PM-1625W

                • KT-105

                  KT-105

                • PM7108

                  PM7108

                • PM2890W

                  PM2890W

                橡膠脫模劑 您現在所有位置:主頁 > 脫模劑系列 > 橡膠脫模劑 >

                PM2890W

                作者:脫模劑管理員??發布時間:2019-12-01
                Perma-Mold® 2890W is a high performance
                mandrel lubricant. When properly applied,
                this formula provides excellent lubrication
                between the mandrel and the cured part,
                resulting in good uniformity and easy
                release. Perma-Mold® 2890W must be
                applied each molding cycle.
                Perma-Mold® 2890W performs well on a
                variety of mandrel designs and rubber
                stocks. The product is ready-to-use and
                should not be mixed with other lubricants or
                solvents.
                Typical Properties
                Appearance
                Off-white fluid
                Density, lbs/gal; kg/l
                8.26; 0.99
                Flash Point (°F)
                None-to-boil
                Storage Stability, unopened 12 months
                Application
                For best performance, the mandrel should
                be cleaned prior to coating with
                Perma-Mold® 2890W.
                Perma-Mold® 2890W is applied by spray
                gun, sponge, swab, or brush as dictated by
                plant logistics. Perma-Mold® 2890W can be
                applied at ambient temperatures up to a
                maximum of 130°F (54°C). Optimum
                coating weight will depend on specific
                process requirements. Perma-Mold® 2890W
                should be coated onto the mandrel prior to
                hose or sleeve production
                Storage
                Store between 50°F-130°F (10°C-54°C).
                Keep from freezing. Keep container tightly
                sealed to prevent evaporation and/or
                contamination. If stored in cold
                temperatures, allow product to warm to room
                temperature prior to use.
                Handling
                We believe Perma-Mold® 2890W has a low
                degree of hazard when used as intended.
                For more information, request a copy of
                Chem-Trend's Material Safety Data Sheet.
                Packaging
                Perma-Mold® 2890W is available in 1-gallon
                (3.8L), 5-gallon (20-liter) or 55-gallon (208-
                liter) containers.
                While the technical information and suggestions for use
                contained herein are believed to be accurate and reliable,
                nothing stated in this bulletin is to be taken as a warranty
                either expressed or implied.
                Perma-Mold® 2890W
                Mandrel Lubricant
                Further Information
                Request information on our complete range of
                materials: custom-formulated release agents for
                polyurethane molding; tire lubes and bladder
                coatings; Mono-Coat® semi-permanent release
                coatings; aerosol formulations; mold cleaners and
                sealers; specialized coatings and application
                equipment.
                上一篇:PM7108 下一篇:沒有了
                男女做受性高爱潮叫床动态图